interface=vap0 driver=nl80211 logger_syslog=-1 logger_syslog_level=2 logger_stdout=-1 logger_stdout_level=2 ctrl_interface=/var/run/hostapd ctrl_interface_group=0 ssid=ABCD-1234 bssid=c4:4b:d1:ae:30:b3 country_code=US ieee80211d=0 ieee80211h=0 ieee80211w=0 hw_mode=a ieee80211n=1 ieee80211ac=1 beacon_int=240 dtim_period=2 max_num_sta=2007 rts_threshold=2347 preamble=0 macaddr_acl=0 auth_algs=1 ignore_broadcast_ssid=0 # Enable HT modes if you want 300Mbps+ throughput. #ht_capab=[HT20][HT40-][HT40+][GF][SHORT-GI-20][SHORT-GI-40] # [TX-STBC][RX-STBC123][MAX-AMSDU-7935][DSSS_CCK-40][PSMP][LSIG-TXOP-PROT] ht_capab=[HT20][HT40+][SHORT-GI-40][SHORT-GI-20] vht_capab=[MAX-MPDU-11454][RXLDPC][RX-STBC-1][MAX-A-MPDU-LEN-EXP0][RX-ANTENNA-PATTERN][TX-ANTENNA-PATTERN][TX-STBC-2BY1][SHORT-GI-80] wmm_enabled=1 wmm_ac_bk_cwmin=4 wmm_ac_bk_cwmax=10 wmm_ac_bk_aifs=7 wmm_ac_bk_txop_limit=0 wmm_ac_bk_acm=0 wmm_ac_be_aifs=3 wmm_ac_be_cwmin=4 wmm_ac_be_cwmax=10 wmm_ac_be_txop_limit=0 wmm_ac_be_acm=0 wmm_ac_vi_aifs=2 wmm_ac_vi_cwmin=3 wmm_ac_vi_cwmax=4 wmm_ac_vi_txop_limit=94 wmm_ac_vi_acm=0 wmm_ac_vo_aifs=2 wmm_ac_vo_cwmin=2 wmm_ac_vo_cwmax=3 wmm_ac_vo_txop_limit=47 wmm_ac_vo_acm=0 ### TX queue parameters tx_queue_data3_aifs=7 tx_queue_data3_cwmin=15 tx_queue_data3_cwmax=1023 tx_queue_data3_burst=0 tx_queue_data2_aifs=3 tx_queue_data2_cwmin=15 tx_queue_data2_cwmax=63 tx_queue_data2_burst=0 tx_queue_data1_aifs=1 tx_queue_data1_cwmin=7 tx_queue_data1_cwmax=15 tx_queue_data1_burst=3.0 tx_queue_data0_aifs=1 tx_queue_data0_cwmin=3 tx_queue_data0_cwmax=7 tx_queue_data0_burst=1.5 vht_oper_centr_freq_seg0_idx=42 vht_oper_chwidth=1 channel=36 supported_rates=60 90 120 180 240 360 480 540 ieee8021x=1 own_ip_addr=127.0.0.1 auth_server_addr=127.0.0.1 auth_server_port=1820 auth_server_shared_secret=lanforge osen=1 #no_pri_sec_switch=1 ocsp_stapling_response=/home/lanforge/hs20/ca/ocsp-server-cache.der