|
||
| Network Testing and Emulation Solutions |
|
|
||
| Network Testing and Emulation Solutions |
5. Routed Mode WanLink with WanPaths
Goal: Setup a Routed Mode WanLink with WanPaths. Return to LANforge-ICE Cookbook
In this test scenario, LANforge-ICE is used to filter traffic by IP address on a WanLink with the use of WanPaths.
| A: Go to the Status tab and click Netsmith |
 |
| B: Right-click in the Netsmith window and select New Connection |
 |
| C: Accept defaults, Auto Create everything and click OK |
 |
| D: Click Apply in the Netsmith window to create the connection |
 |
| E: The Netsmith window after applying changes |
 |
| A: Right-click the WanLink and select Modify WanLink |
 |
| B: Setup the WanLink with values larger than what each of the
WanPaths will use
• WanPaths are subordinate to WanLinks. WanLinks, therefore, should be configured with sufficient bandwidth and buffering required by all of its WanPaths • Click Apply and leave the Create/Modify WanLink window open |
 |
| A: Click Create-WP on Entry Point A to create a new
WanPath on this WanLink
• NOTE: In order to filter by specific IP address, use a Source and Dest Mask of 32 to exactly match the IP coming in on the Entry Point • Click OK to create the WanPath |
 |
| B: Click Create-WP on Entry Point B to create a new
WanPath on this WanLink
• NOTE: The Source and Destination IPs for this WanPath are the reverse of those for Entry Point A • Click OK to create the WanPath |
 |
| C: Create a second WanPath for this WanLink using the next set of IP addresses |
 |
| D: Reverse the Source and Destination IPs for this corresponding WanPath |
 |
| E: Verify that the WanPaths on this WanLink are setup correctly, then click OK on the Create/Modify WanLink window shown here |
 |
| A: Right-click on the WanLink and select Toggle Wanlink |
 |
| B: Right-click port rddVR0 and select Modify Port |
 |
| C: Setup an IP address that is on a different network than the WanPath entry points |
 |
| D: Setup an IP address on port rddVR1 that is on the same network as rddVR0 |
 |
| A: Right-click in the Netsmith window and select New Router |
 |
| B: Accept the defaults or change the Virtual Router name and graphical size |
 |
| C: Click the Apply button and repeat for the
second Virtual Router
• NOTE: After making any changes to the Netsmith window, you must click Apply or your changes will NOT be implemented and could be lost • NOTE: Clicking Sync makes sure any changes are synchronized with the current database |
 |
| D: Left-click rddVR0 and drag it inside Router R0(1) |
 |
| E: Left-click rddVR1 and drag it inside Router R1(2) |
 |
| F: Apply your changes in Netsmith |
 |
| A: Right-click port eth0 and select Modify Port |
 |
| B: Setup eth0 with a valid IP address and IP mask that is on the same network as the WanPath entry points ep-1 and ep-3 |
 |
| C: Left-click port eth0 and drag it inside Router R0(1) |
 |
| D: Setup eth1 with a valid IP address and IP mask that is on the same network as the WanPath entry points ep-2 and ep-4 |
 |
| E: Drag eth1 inside Router R1(2) and Apply changes in Netsmith |
 |
| A: Right-click the WanLink and select Display Wanlink |
 |
| B: The lower half of the WanLink display shows traffic passing on WanPath entry points ep-3 and ep-4 and other IP address are excluded from passing on the WanLink |
 |
| C: Select a WanPath and click Display Selected Paths in the lower left corner of the WanLink display window |
 |
Email Candela Technologies at: support@candelatech.com if you have any questions or suggestions.
www.candelatech.com | sales@candelatech.com | +1 360 380 1618
Candela Technologies, 2026 Main Street, Suite A, P.O. Box 3285, Ferndale, WA 98248, USA
www.candelatech.com |
sales@candelatech.com | +1 360 380 1618
Last modified: Fri Mar 11 09:53:40 PST 2011
